Important Plumbing Tips for Bathtub Installation
Important Plumbing Tips for Bathtub Installation
Blog Article
What are your ideas with regards to How to Install a Bathtub?
Installing a tub isn't specifically rocket science, but it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately difficult project. If the old bathtub is conveniently obtainable, the task can relocate immediately; if you need to open up a wall surface to eliminate the old tub and place the brand-new tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will require an assistant to vacate the old bathtub and also set in the new one. Make sure you have actually certified yourself for the task and fit attempting it. Instead of hiring a contractor to take control of a halfway-completed project, it is far better to think about using one before you start. Chances are you might need a specialist plumber to make tube connections.
This post will assist you mount a new tub in your bathroom if you have currently acquired a new tub as well as do not need to change the plan of your previous supply of water pipelines.
Your tools and material checklist must consist of the following:
Planning for the Installment
To start with, the sustaining structure supplied with the bathroom needs to be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable tap adapters to the bottom of both taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you make use of every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its final placement.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water. After doing so, activate the faucets to drain any kind of water remaining in the system. The process of getting rid of the existing faucets can be quite bothersome due to the restricted access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the staying water that will come from the pipes. When the supply pipes have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
Before going on to fit the brand-new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the required placement. The wood boards are useful in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the tub till the spirit level checks out degree.
To install faucets, fit all-time low of the furthest flexible faucet connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the other tap.
Switch on the water supply and inspect all joints and also new pipework for leakages and tighten them if required. Fill up the tub as well as likewise examine the overflow outlet and the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait till the tub has actually been utilized at least when as this will resolve it into its final placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin guaranteeing that the washers are in place in between the tap as well as the sink. Secure the faucet in position with the maker offered backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind should be connected to the tap finishes initially, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to break a stiff seal, causing the water to permeate the wall surface in between the bathroom and also the tiling, leading to problems with moisture as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components and also installations. They are marketed in tubes as well as cartridges, as well as can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to permit the motion experienced when the tub remains in usage. The sealer can break fairly very early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently readily available on the marketplace. It is recommended to fit the tiles using waterproof or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our part about A Step-by-Step Guide to Installing a Bathtub. Thanks so much for taking the time to browse our blog. Sharing is caring. Helping people is fun. Thank-you for your time spent reading it.
Ensure plumbing integrity; reach out. Report this page